Pioneer Premier PRS Mono Class D Amplifier - PRS-D1200M

Product Details

Pioneer Premier PRS Mono Class D Amplifier, Model PRSD1200M

Features:

• Rock the House with Premier PRS Amplifiers
  Round out your PRS system with the Premier PRS-D1200M, designed to complement the new PRS-D4200F and PRS-D2200T amplifiers. Drive your subwoofers with authority with this powerful and clean-sounding amplifier
• Superior Channel Separation
  PRS amplifiers feature Left and Right independent signal circuitry that eliminates signal interference between the channels and achieves excellent channel separation throughout a wider frequency range
• Full Custom-Made Power Supply Capacitor Bank
  In the quest for optimal bass, Pioneer focused on the PRS amplifier’s power handling. With a high-capacity, custom-made capacitor bank adapted to the power supply section, this amp supplies power with rock-solid stability, and does an excellent job of reproducing low-frequency sound
• Linear Technology Operational Amplifier
  The PRS amplifier features this Linear Technology Corporation operational amplifier (OP AMP) used in high-end home audio amplifiers for its precise gain and sound linearity characteristics. The PRS-D1200M includes the OP AMP in its bass boost circuitry to prevent sound quality deterioration
• Externally Bridgeable
  The units are externally bridgeable and permit two separate amplifiers to be joined together as one, doubling the power to a single woofer or voice coil. Best of all, no special cable is required - a simple RCA cable and proper setting of the Sync mode will get this
• Multi-Amplifier Synchronization System (MASS)
  Pioneer's proprietary Multi-Amplifier Synchronization System (MASS) technology allows one amplifier (the master) to control the settings of other amplifiers when two or more amps are “strapped” together. Especially important for multi-amplified systems, this powerful Pioneer technology eliminates the need to adjust each amplifier gain separately
• Variable Crossover (40~240Hz, LPF)
  For added flexibility, the variable crossover lets you set the levels at which higher-frequency signals will be filtered out, so that the remaining lower-frequency signals get sent to your sub(s). Where they belong. This optimizes your system's efficiency and delivers the best possible sound quality. You can adjust it continuously between 40 to 240Hz
• Selectable Bass Boost with Wired Bass Remote
  So you're in the driver's seat going 65mph and you want to fine-tune the bass boost. But the amp's out of reach, way in the back. What are you supposed to do — pull over, get out, and run around to the trunk? That's why the PRS-D1200M comes with a wired bass remote. It's set at 50Hz, ideal for tuning in some more thump from your subwoofers. And because this is selectable bass boost, you can set the level at 0dB, 6dB, or 12dB, whichever sounds best to you
• Speaker Level Inputs
  What, you DON'T own a Pioneer headunit? Well, we won't hold it against you. In fact we'll even help you build onto your system. The PRS-D1200M's speaker level inputs allow you to connect your OEM unit (or any unit that doesn't have the typical RCA-type inputs) without having to buy add-on adapters
  

Specifications:

General

• Peak Music Power: 1200 Watts
  
• Number of Channels: 1
  
• Load Impedance Capability: 1~8 Ohm
  
• Continuous Power (4 ohm): 400 W x 1
  
• Continuous Power (2 ohm): 600 W x 1
  
• Frequency Response: 10Hz ~ 240Hz
  
• Total Harmonic Distortion: 0.5%
  
• Signal-to-Noise Ratio: 92 dB

Features

• Channel # Capability: 1
  
• Class-D Design
  
• PWM Regulated MOSFET Power Supply
  
• MOSFET Output Section
  
• Screw-Type Speaker Terminals
  
• Balanced Isolator Input Circuit
  
• RCA Inputs: 2 Channel (Gold)
  
• Speaker Level Input: Yes
  
• Input Level Control: Hi-Volt (400mV~6.5V)
  
• Built-in Crossover: LPF
  
• Crossover Frequency Range: 40~240Hz, -18dB/Oct.
  
• Bass Level Control: 50Hz, 0/6/9/12dB, with Remote
  

CEA 2006 Specifications

• Output Power (4 Ohm, <=1% THD): 400 Watts x 1
  
• Output Power (2 Ohm, <=1% THD): 600 Watts x 1
  
• Signal to Noise (1 Watt into 4 Ohms): 66 dBA

Approximate Dimensions:

• Width: 11.9375"
  
• Height: 2.1875"
• Depth: 7.6875"

Approximate Weight:

• Shipping: 6 lbs

Warranty

Abt Extended Service Protect your products with the Abt extended protection plan. Abt Local 4 Year Protection Plan - details $39.00 select We're sorry, but we're unable to offer an extended warranty to your zipcode. enter zip code for pricing Update Zip Code Zip Code

Questions and Answers