Cicada Audio FLX 4-Channel Motorcycle Amplifier - FLX2000.4
- 331W RMS X 4-Channel Amplifier (4-Ohm/14.4Vdc)
- Small Footprint Design
- Variable Low-Pass Crossover
- Variable High-Pass Crossover
- 8V-16V Operating Voltage
- 79% Total Efficiency
- REM/DC Turn-On Configuration
- 1044W RMS X 2-Channel Bridged (4-Ohm/14.4Vdc)
- Brushed Aluminum Finish
Cicada Audio FLX2000.4 FLX 4-Channel Motorcycle Amplifier
The Cicada Audio FLX2000.4 FLX series four-channel motorcycle amplifier delivers 4 x 331 W RMS into 4 ohms or 4 x 542 W RMS into 2 ohms at 14.4 Vdc. Two-channel bridged operation provides 2 x 1044 W RMS into 4 ohms at 14.4 Vdc, while LPF/FULL/HPF selection adds a 30-300 Hz crossover with a 12 dB-per-octave slope. Compact motorcycle-focused packaging, adjustable gain and REM/DC turn-on configuration help installers build a higher-output sound system where installation space is limited.
Key Features
Four Channels or Two-Channel Bridged Mono
Keep four channels for your speaker layout or choose two-channel bridged mono operation to suit the build. At 12.5 Vdc, output is 4 x 275 W RMS into 4 ohms or 4 x 450 W RMS into 2 ohms; the bridged rating is 2 x 866 W RMS into 4 ohms. Match the configuration and supply-voltage rating to your system when planning speaker loads.
Selectable LPF/FULL/HPF Filtering
Choose low-pass filtering to limit higher frequencies, high-pass filtering to limit lower frequencies, or FULL for full-range operation. Adjustable crossover frequency lets the installer tailor the cutoff to the speakers being driven instead of working with a fixed filter point.
0.2-12 Vac Gain and REM/DC Turn-On
Use the 0.2-12 Vac gain range to match input sensitivity to the source signal during setup. REM/DC turn-on configuration provides another installation choice, allowing the installer to select the turn-on mode for the system.
Flexible. Powerful. Purpose-Built.
Engineered for motorcycles, the FLX platform pairs substantial output with compact packaging and mounting flexibility for space-limited sound-system builds. Plan the electrical installation alongside the speaker layout: a lithium battery upgrade and 4 AWG power wire are required.
Features
- 331 W RMS x 4 at 4 Ohms / 14.4 Vdc
Four powered channels support a multi-speaker motorcycle audio setup. - 542 W RMS x 4 at 2 Ohms / 14.4 Vdc
A 2-ohm load offers the higher four-channel output rating. - 1044 W RMS x 2 Bridged at 4 Ohms / 14.4 Vdc
Configure the amplifier for two-channel bridged mono operation. - LPF/FULL/HPF Selection
Choose low-pass, full-range or high-pass operation for your speaker configuration. - 30-300 Hz Crossover, 12 dB per Octave
Tune the frequency cutoff for the speakers in your build. - 0.2-12 Vac Adjustable Gain
Set input sensitivity to suit the incoming audio signal. - REM/DC Turn-On Configuration
Select the turn-on mode appropriate for the installation. - Compact FLX Design
Motorcycle-oriented packaging makes the most of limited mounting space. - 8-16 V Operating Range
Check the supply-voltage range when planning your electrical system. - 60 A Music Current Draw
Plan electrical support around a 240 A maximum draw and a 120 A recommended music fuse.
Footnotes:
Installation requires a lithium battery upgrade and 4 AWG power wire.
Performance figures reflect manufacturer testing under specific conditions and may vary with the installation, settings and use.
Similar Products (4 items)
Related Guides and Articles
Frequently Asked Questions
-
At 14.4 Vdc, output is 331 watts RMS per channel into 4 ohms or 542 watts RMS per channel into 2 ohms. At 12.5 Vdc, output is 275 watts RMS per channel into 4 ohms or 450 watts RMS per channel into 2 ohms. Power output depends on speaker impedance and supply voltage.
-
Installation requires a lithium battery upgrade and 4 AWG power wire. The manufacturer lists a 120 A recommended fuse for music use, 60 A current draw during music playback and 240 A maximum current draw. The operating voltage range is 8 to 16 V. These installation requirements do not indicate that a battery, wiring or fuse is included.
-
Yes. Two-channel bridged mono operation is supported into 4-ohm loads. Bridged output is 866 watts RMS per channel at 12.5 Vdc or 1,044 watts RMS per channel at 14.4 Vdc.
-
Published dimensions are 9.2 x 4.9 x 2 in (233.68 x 124 x 51 mm). The manufacturer does not label the measurement axes or specify whether these dimensions include mounting brackets, so account for that uncertainty when planning installation space.
-
Selectable low-pass (LPF), full-range (FULL) and high-pass (HPF) modes let you configure the audio filtering. The published crossover adjustment range is 30 to 300 Hz, with a 12 dB-per-octave slope. Adjustable gain has a published input range of 0.2 to 12 Vac for input-level matching.
