Cicada Audio 6.5-Inch Component Speaker Kit for 2024+ H-D Road Glide - 24CXK65.2RG

Cicada Audio 24CXK65.2RG 6.5-Inch Component Speaker Kit for 2024+ H-D Road Glide

The Cicada Audio 24CXK65.2RG motorcycle component speaker kit pairs a 6.5 in, 2-ohm mid-bass driver with a 1 in, 4-ohm shallow ring radiator horn tweeter for 2024+ H-D Road Glide factory speaker locations. Power handling is rated separately at 250W RMS for the mid-bass and 200W RMS for the tweeter. Rain or Shine construction supports outdoor use, while a Carbon Matrix Composite cone and OFC copper components emphasize efficient, heat-tolerant performance. A die-cast aluminum basket with Vortex Flow Venting and an external crossover with tweeter attenuation round out this vehicle-specific audio upgrade.

Key Features

Road Glide Fitment, Rain or Shine

Built around the factory speaker locations on 2024+ H-D Road Glide motorcycles, the kit is designed for an application-specific upgrade. Rain or Shine construction brings a weather-oriented design to speakers intended for outdoor motorcycle use.

OFC Copper Shorting Ring and Carbon Matrix Composite Cone

The OFC copper shorting ring helps extend upper-frequency performance from the mid-bass driver. Its Carbon Matrix Composite cone combines low mass, rigidity and heat tolerance, emphasizing efficient performance through the choice of cone material.

OFC Copper Voice-Coil Wire With Black Coat

Conductivity, low resistance and thermal capability guide the voice-coil construction. OFC copper wire with Black Coat treatment complements the heat-tolerant cone, while the mid-bass driver carries a separate 250W RMS/500W MAX power-handling rating.

N35SH Neodymium Motor and Vortex Flow Venting

An N35SH neodymium motor anchors the mid-bass design. The custom die-cast aluminum basket incorporates Vortex Flow Venting, adding dedicated ventilation to complement the thermal capabilities of the cone and voice-coil materials.

1 in Shallow Ring Radiator Horn Tweeter

The high-frequency side of the upgrade uses a shallow ring radiator horn design with an aluminum dome and neodymium magnet. The tweeter operates at 4 ohms rather than the mid-bass driver's 2 ohms. Its 200W RMS/400W MAX power handling is a separate driver rating; the two drivers' ratings should not be added together as a system total.

External Crossover With -3/-6 dB Tweeter Attenuation

Choose -3 dB or -6 dB attenuation to reduce tweeter output when tailoring the sound balance. The external 12dB-7kHz crossover has a custom-tooled, vented enclosure, with a heat-sink-enclosed resistor crossover for tweeter attenuation.

Features

• 2024+ H-D Road Glide Factory-Location Fit
  Targets the factory speaker locations on the specified motorcycle application.
• Rain or Shine Construction
  Weather-oriented materials support outdoor audio use.
• OFC Copper Shorting Ring
  Helps the mid-bass driver reach into upper frequencies.
• Carbon Matrix Composite Cone
  Balances low mass and rigidity with heat tolerance.
• 6.5 in, 2-Ohm Mid-Bass Driver
  Handles 250W RMS/500W MAX independently of the tweeter rating.
• OFC Copper Voice-Coil Wire With Black Coat
  Pairs low-resistance copper with a thermally capable treatment.
• N35SH Neodymium Motor
  Uses neodymium construction in the mid-bass driver.
• Die-Cast Aluminum Basket With Vortex Flow Venting
  Combines a custom driver support structure with dedicated ventilation.
• 1 in, 4-Ohm Ring Radiator Horn Tweeter
  Features an aluminum dome, neodymium magnet and separate 200W RMS/400W MAX rating.
• External 12dB-7kHz Crossover
  Houses the crossover in a custom-tooled, vented enclosure.
• -3/-6 dB Tweeter Attenuation
  Provides two output-reduction options through a heat-sink-enclosed resistor crossover.

Footnotes:

Performance figures reflect manufacturer testing under specific conditions and may vary with installation, settings and use.