Cicada Audio CXK 6.5-Inch Component Speaker Kit for 2024+ H-D Street Glide - 24CXK65.2SG
- 6.5-Inch Motorcycle Component Speaker Kit
- 250W RMS Mid-Bass Power Handling
- 2024+ H-D Street Glide Factory Fitment
- All-Weather Performance Design
- 1-Inch 4-Ohm Aluminum Ring-Radiator Horn Tweeter
- External Vented Crossover
- 2-Ohm Mid-Bass Impedance
- Carbon Matrix Composite Cone
- N35SH Neodymium Magnet Motor
- Black Finish
Cicada Audio 24CXK65.2SG CXK 6.5-Inch Component Speaker Kit for 2024+ H-D Street Glide
The Cicada Audio 24CXK65.2SG CXK component motorcycle speaker kit is designed for 2024+ H-D Street Glide factory locations, pairing 6.5-in, 2-ohm mid-bass drivers with 1-in, 4-ohm shallow ring-radiator horn tweeters. Its Rain or Shine all-weather design combines Carbon Matrix Composite cones, OFC copper voice-coil wire with Black Coat and neodymium magnets for a motorcycle-focused upgrade. An external crossover with -3/-6 dB tweeter attenuation lets riders tailor the high-frequency level.
Key Features
2024+ H-D Street Glide Factory-Location Fit
Start with the intended installation: the factory-designed speaker locations on 2024+ H-D Street Glide motorcycles, rather than a universal mounting application. Rain or Shine construction addresses exposure to the elements with an all-weather design built around motorcycle use.
OFC Copper and Black Coat
The OFC copper shorting ring is designed to extend high-frequency performance. In the voice coil, OFC copper wire emphasizes conductivity and low resistance, while Black Coat treatment supports thermal performance. These material choices address both the electrical and thermal demands of the speaker's voice-coil construction.
Carbon Matrix Composite and Vortex Flow Venting
Low mass, strength, high-temperature resistance and efficiency come together in the Carbon Matrix Composite cone, putting the material emphasis on the moving surface that produces the mid-bass. An N35SH neodymium magnet motor and a custom-tooled die-cast aluminum basket complete the supporting construction. Vortex Flow Venting is incorporated into the basket design.
Ring-Radiator Horn Tweeters and External Crossover
The high-frequency side uses aluminum-dome tweeters with a shallow ring-radiator horn design and a separate 4-ohm specification. The external 12dB-7kHz crossover is custom-tooled, vented and encased. A heat sink encased resistor crossover provides -3/-6 dB attenuation, giving you a choice of tweeter-level reduction within the component setup.
Features
- 2024+ H-D Street Glide Fitment
Designed for the motorcycle's factory speaker locations. - Rain or Shine All-Weather Design
Built for motorcycle use and exposure to the elements. - OFC Copper Shorting Ring
Extends the speaker's high-frequency performance. - OFC Copper Voice-Coil Wire With Black Coat
Combines conductivity and low resistance with thermal performance. - Carbon Matrix Composite Cone
Supports efficient mid-bass reproduction with a lightweight, strong, heat-resistant material. - N35SH Neodymium Magnet Motor
Uses neodymium in the speaker motor's construction. - Die-Cast Aluminum Basket With Vortex Flow Venting
Integrates venting into the custom-tooled speaker basket. - 1-in, 4-Ohm Ring-Radiator Horn Tweeters
Aluminum domes handle high-frequency reproduction in a shallow component design. - External 12dB-7kHz Crossover
Uses a custom-tooled, vented enclosure for the crossover. - -3/-6 dB Tweeter Attenuation
Offers two levels of high-frequency reduction through a heat sink encased resistor crossover.
Related Guides and Articles
Frequently Asked Questions
-
The mid-bass driver is rated for 250W RMS and 500W maximum power handling. The tweeter is rated separately for 200W RMS and 400W maximum. These are component-specific ratings, not a combined whole-kit power rating.
-
The speakers are designed for all-weather performance under the manufacturer's Rain or Shine designation. No numerical ingress-protection rating is published.
-
The mid-bass driver has a 2-ohm impedance, while the shallow ring-radiator horn tweeter has a 4-ohm impedance. The two component types have separate impedance specifications.
-
The published tweeter attenuation options are -3 dB and -6 dB, using a heat sink-encased resistor crossover. The tweeter specifications also list an external, vented, encased 12 dB crossover at 7 kHz.
-
The manufacturer's warranty provides two years of manufacturing-defect coverage and requires proof of purchase from the original purchaser. Claims must be submitted through the online warranty form, and written authorization with an RA number is required before returning any items.
