Zoeller 260 Series Waste-Mate Sump Pump - M267

Zoeller 260 Series Waste-Mate Sump Pump - M267

Submersible sewage/effluent or dewatering pump

Features:

• Float-operated, 2-pole mechanical switch
• Durable cast construction, ASTM Class 25 cast iron switch case and pump housing
• Cast iron base on model 267
• Engineered plastic base on model 266
• Non-clogging vortex impeller design. Engineered plastic impeller with metal inserts (1 Ph). Model 267 available with cast iron impeller (standard on 3 Ph models).
• Not affected by materials normally found in drainage and sewage pumps
• Stainless steel screws, bolts, handle, guard and arm and seal assembly
• Neoprene square ring and gasket
• Oil-filled, hermetically-sealed motor
• Oil-lubricated bearings
• Carbon and ceramic shaft seal
• Passes 2” (50 mm) spherical solids
• 2” female and 3" NPT male discharge
• On point: 12” (30 cm) (automatic units)
• Off point: 4” (10 cm) (automatic units)
• Corrosion-resistant, powder coated epoxy finish
• Completely submersible
• Watertight and dust-tight
• Automatic and non-automatic models available
• Models available packaged with a piggyback variable level float switch
• Automatic reset thermal overload protection (1 Ph only)

Specifications:

• Minimum recommended basin size (small load applications):
  • simplex: 18” x 30” (45.7 x 76.2 cm)
  • duplex: 30” x 36” (76.2 x 91.4 cm)
• Approximate gallons pumped out per cycle for standard models:

• Hertz: 60 Hz
• Motor: 1/2 Hp
• Voltage: 115 - 460 V
• Phase: 1 Or 3 Ph
• RPM: 1750 RPM
• Type: Split Phase Or 3 Phase
• Insulation: Class B
• Amps: 1.5 - 10.4 Amps
• Operation: Automatic Or Non-automatic
• Auto On/ Off Points: 12" / 4" (30 Cm / 10 Cm)
• Discharge Size: 2" Or 3" Npt
• Solids Handling: 2" (50 Mm) Spherical Solids
• Cord Length: 10' (3 M) Auto, 15' (5 M) Non-auto Standard
• Cord Type: Ul Listed, 3-Wire Neoprene Cord And Plug
• Max Head: 21.5' (6.6 M)
• Max Flow Rate: 128 GPM (484 Lpm)
• Max Operating Temp: 130 °F (54 °C)
• Cooling: Oil Filled
• Motor Protection: Auto Reset Thermal Overload (1 Ph)
• Cap: Cast Iron
• Motor Housing: Cast Iron
• Pump Housing: Cast Iron
• Base: Cast Iron Or Engineered Plastic
• Upper Bearing: Sleeve Bearing
• Lower Bearing: Sleeve Bearing
• Mechanical Seals: Carbon And Ceramic
• Impeller Type: Non-Clogging Vortex
• Impeller: Engineered Plastic With Metal Insert
• Hardware: Stainless Steel
• Motor Shaft: Aisi 1215 Cold Rolled Steel
• Gasket: Neoprene

Caution

• All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).
• Maximum temperature of sewage or dewatering must be limited to 130°F (54°C). For over 130°F (54°C) special quotation required.

Approximate Dimensions:

• Height: 14.31"
• Width: 13.07"
• Depth: 11.03"

Approximate Weight:

• Shipping: 47.5 lbs

Warranty Information:

• Manufacturer Warranty (authorized online retailer): 3 Years Limited