Cicada Audio Larry Frederick Classic 6.5-Inch 4-Ohm Coaxial Horn Speakers (Pair) - CH65.4C
- 6.5-Inch Coaxial Horn Speaker Pair
- 4-Ohm Impedance
- 250W RMS / 500W Max Power
- N35SH Neodymium Magnet Structure
- Water-Resistant Treated Paper Cone
- Black-Coat OFC Copper Voice Coil
- Aluminum Diaphragm Horn Tweeter
- External 12dB Crossover Network
- 96.4dB Sensitivity
- Black Finish
Cicada Audio CH65.4C Larry Frederick Classic 6.5-Inch 4-Ohm Coaxial Horn Speakers (Pair)
The Cicada Audio CH65.4C Larry Frederick Classic 6.5-in coaxial horn motorcycle speakers are sold as a pair and feature 4-ohm impedance, 250W RMS / 500W maximum power handling, 96.4 dB sensitivity at 1W/1m and an external 12 dB crossover at 4 kHz. They are designed for 2014+ H-D factory locations, with the included spacer required on some models. An aluminum tweeter diaphragm adds brighter treble, while a lightweight, water-resistant treated paper cone supports efficient mid-bass performance and high-temperature resistance.
Key Features
Larry Frederick Original Classic Design and Factory-Location Fit
Built around Larry Frederick Original Classic Design, the pair is intended for existing 2014+ H-D factory speaker positions. Some models require the included 0.5-in spacer, so check the specific application rather than assuming the same fit on every motorcycle.
Aluminum Tweeter and External 12 dB Crossover
The high-frequency section pairs an aluminum diaphragm with a 1.4-in/36mm tweeter voice coil. OFC copper winding supports sound quality with reduced heat generation, complementing the diaphragm's emphasis on treble brightness and efficiency. A custom-tooled, ventilated enclosure houses the external crossover network, specified at 12 dB at 4 kHz.
Water-Resistant Cone and Black Coat Voice Coil
For mid-bass reproduction, treated paper keeps the cone light while providing water resistance and high-temperature tolerance. The 2-in/51mm main voice coil uses OFC copper with Black Coat treatment to support conductivity, reduced electrical resistance and heat-handling performance. Water resistance applies specifically to the cone, not to the entire speaker assembly.
N35SH Neodymium Motor and Vortex Flow Venting
An N35SH-grade neodymium magnet forms the motor, while a custom-tooled die-cast aluminum basket supports the driver assembly. The basket incorporates Vortex Flow Venting, integrating ventilation into the frame alongside the cone and voice-coil construction.
Features
- Larry Frederick Original Classic Design
Includes two 6.5-in, 4-ohm coaxial horn speakers. - 2014+ H-D Factory Locations
Designed for applicable factory positions; some models require the included 0.5-in spacer. - Aluminum Tweeter Diaphragm
Delivers bright treble with efficient operation. - External 12 dB Crossover at 4 kHz
Uses a custom-tooled, ventilated enclosure for the network. - 1.4-in OFC Copper Tweeter Voice Coil
Helps limit heat generation while supporting sound quality. - Water-Resistant Treated Paper Cone
Keeps cone mass low while tolerating high temperatures. - 2-in Black Coat OFC Copper Voice Coil
Supports conductivity and heat handling with reduced electrical resistance. - N35SH Neodymium Magnet Motor
Drives the coaxial horn assembly with a neodymium magnet. - Die-Cast Aluminum Basket With Vortex Flow Venting
Combines a custom-tooled metal frame with integrated venting. - 250W RMS / 500W Maximum Power Handling
Rated for 4-ohm motorcycle audio applications. - 96.4 dB Sensitivity
Specifies output at 1W input and a 1m measuring distance. - 75 Hz - 20 kHz Frequency Response
Covers the rated audio range within +/-5 dB.
Footnotes:
Performance figures are based on manufacturer testing under specific conditions and may vary with installation, settings and use.
Related Guides and Articles
Frequently Asked Questions
-
The published power handling is 250W RMS and 500W maximum. The manufacturer does not specify whether these ratings apply per speaker or to the pair.
-
The treated-paper cones are water resistant, but this does not establish that the complete speakers are waterproof. No waterproof or IP rating is published.
-
The published mounting depth is 3.0 in (76.2 mm), and the mounting diameter is 5.7 in (145.5 mm). An included 0.5-in spacer is required for some installations; these measurements alone do not guarantee compatibility.
-
The published frequency response is 75 Hz to 20 kHz, with a tolerance of +/-5 dB. Sensitivity is rated at 96.4 dB at 1W/1m, and the external crossover uses a 12 dB network at 4 kHz.
-
A two-year manufacturer warranty covers manufacturing defects for the original buyer with proof of purchase. The manufacturer determines whether to repair or replace eligible equipment. Claims must be submitted through the online warranty form, and written authorization with a valid RA number is required before shipping.
